User Tag List

Page 48 of 48 FirstFirst ... 38464748
Results 1,176 to 1,181 of 1181

Thread: MITYAZ GSR Build Thread

  1. #1176
    Senior Member mityaz's Avatar
    Join Date
    Sep 2016
    Posts
    1,337
    Mentioned
    70 Post(s)
    Tagged
    0 Thread(s)
    @razorlab yea, theoretically at 8500rpm my speed in 4th gear is 140mph. At 8800rpm it would be 144+mph.
    At NJMP Lightning i was hitting 145mph in 5th with stock final drive. That shift was definitely cumbersome and thats the time where i had that off road mishap. The acceleration definitely trails off at those speeds. I also have that big parachute on the trunk in the form of gtc300. Im sure that hurts my drag coeff significantly

    Sent from my SM-G950U using Tapatalk
    '11 GSR
    current: same exact as last. new block, new head. no kaboom yet.

    2.05L/darton,ProH,CP 10:1 w/Ultimate pins. IWG9174 .92. GSC-S2. 4P head +1mm In/Ex. <--KABOOM (blown HG)

    Past: 2.4L,Manley94,Pro-H,Wiseco,10:1,Darton,4P head,GSC all,Supertec valves,FR 9174 IWG .92,2x450 Walbro/EP control,ID1700,Flex,OSGiken triple. <--KABOOM (spun rod bearing)

  2. #1177
    Senior Member mityaz's Avatar
    Join Date
    Sep 2016
    Posts
    1,337
    Mentioned
    70 Post(s)
    Tagged
    0 Thread(s)
    While all of y'all are complaining about evos... i am installing the RCK/ bump steer kit. Track fay in a few weeks...
    .
    .
    .

    Sent from my SM-G950U using Tapatalk
    '11 GSR
    current: same exact as last. new block, new head. no kaboom yet.

    2.05L/darton,ProH,CP 10:1 w/Ultimate pins. IWG9174 .92. GSC-S2. 4P head +1mm In/Ex. <--KABOOM (blown HG)

    Past: 2.4L,Manley94,Pro-H,Wiseco,10:1,Darton,4P head,GSC all,Supertec valves,FR 9174 IWG .92,2x450 Walbro/EP control,ID1700,Flex,OSGiken triple. <--KABOOM (spun rod bearing)

  3. #1178
    Senior Member mityaz's Avatar
    Join Date
    Sep 2016
    Posts
    1,337
    Mentioned
    70 Post(s)
    Tagged
    0 Thread(s)
    After completing the RCK install i did the alignment (by myself). Went with -3.5F, -2.5R camber. toe in "just a tiny bit" on both.
    I then attempted to put my new set of wheels on with 285 Re71r in 10.5 +25 offset but it was hitting the strut in the front. Fuck. I then had to flip the upper cam bolt around (arrow pointing in) to minimize negative camber at the knuckle. THis messed up my alignment so i had to do it again lol. I'm getting good at it now.

    Went out doing a few pulls. Did a 3-4 gear pull (closed course). The temps are up there. AFR is pretty rich too. I guess i could richen it up a bit more. What do you guys think @Black E @razorlab ?

    https://datazap.me/u/mityaz/282-2-3-...zoom=2981-4174
    '11 GSR
    current: same exact as last. new block, new head. no kaboom yet.

    2.05L/darton,ProH,CP 10:1 w/Ultimate pins. IWG9174 .92. GSC-S2. 4P head +1mm In/Ex. <--KABOOM (blown HG)

    Past: 2.4L,Manley94,Pro-H,Wiseco,10:1,Darton,4P head,GSC all,Supertec valves,FR 9174 IWG .92,2x450 Walbro/EP control,ID1700,Flex,OSGiken triple. <--KABOOM (spun rod bearing)

  4. #1179
    Senior Member razorlab's Avatar
    Join Date
    Aug 2015
    Location
    Bay Area, CA
    Posts
    2,363
    Mentioned
    217 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by mityaz View Post
    Went out doing a few pulls. Did a 3-4 gear pull (closed course). The temps are up there. AFR is pretty rich too. I guess i could richen it up a bit more. What do you guys think @Black E @razorlab ?

    https://datazap.me/u/mityaz/282-2-3-...zoom=2981-4174
    I think it looks consistent across all four runners and doesn't rise much if you look at the average of them all.

    I wouldn't richen it up more, mid to low 11's are rich enough on E85. I still think your timing is too high 7k+.

    See what track day data gives you.

    On a side note, do you have smoothing on high for your AFR channel?

  5. #1180
    Senior Member mityaz's Avatar
    Join Date
    Sep 2016
    Posts
    1,337
    Mentioned
    70 Post(s)
    Tagged
    0 Thread(s)
    ^my alpha for AFR is at 0.1 (just like it is for every other analog channel). Why do you ask?
    Last edited by mityaz; Yesterday at 10:31 AM.
    '11 GSR
    current: same exact as last. new block, new head. no kaboom yet.

    2.05L/darton,ProH,CP 10:1 w/Ultimate pins. IWG9174 .92. GSC-S2. 4P head +1mm In/Ex. <--KABOOM (blown HG)

    Past: 2.4L,Manley94,Pro-H,Wiseco,10:1,Darton,4P head,GSC all,Supertec valves,FR 9174 IWG .92,2x450 Walbro/EP control,ID1700,Flex,OSGiken triple. <--KABOOM (spun rod bearing)

  6. #1181
    Senior Member razorlab's Avatar
    Join Date
    Aug 2015
    Location
    Bay Area, CA
    Posts
    2,363
    Mentioned
    217 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by mityaz View Post
    ^my alpha for AFR is at 0.1 (just like it is for every other analog channel). Why do you ask?
    My afr data stream isn't even close to being that smooth.

    Yours:

    https://datazap.me/u/mityaz/282-2-3-...zoom=3224-3468

    Mine:

    https://datazap.me/u/razorlab/sedyno...&zoom=883-1113

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •